Hello Good day friends, i am having an issue with a Range Rover Evoque 2.0 GTDi engine , throws a code P0299 underboost condition, Checked for Intake Leaks no leaks, Charge air pressure sensor is functional, i am considering the Turbocharger maybe faulty, can anyone assist with a service bulletin for the 2012-2013 Range Rover Evoque 2.0 GTDi , i was aware of a faulty turbocharger issue??? but i am not certain, any help needed or futher advise on this issue or maybe something else i can check before this, thanks in advance..
↧
2013 Range Rover Evoque under Boost problems
↧
FORD T6 IMMOBILIZER PROBLEM
Hi
I am having a problem with Ford T6 2013 model,it will not start but if i leave the key on for a few minutes,say 15-30min it starts and runs ok.As soon as i turn it off it wont start again and i have to do the whole key on for a few minutes again.
Ran IDS and i get error A161A-27 immobilizer sent wrong signal or something to that effect.
When i try to do any PATS function it is taking me to the online option of which i do not have an account.
Can some one help with this,even via Team viewer,willing to pay.
I am having a problem with Ford T6 2013 model,it will not start but if i leave the key on for a few minutes,say 15-30min it starts and runs ok.As soon as i turn it off it wont start again and i have to do the whole key on for a few minutes again.
Ran IDS and i get error A161A-27 immobilizer sent wrong signal or something to that effect.
When i try to do any PATS function it is taking me to the online option of which i do not have an account.
Can some one help with this,even via Team viewer,willing to pay.
↧
↧
ford connect how to program old ecu
i have vcx nano with 112.01 ids softwere
but i cant reset ecu (need access to site)
any ideasyhanks in advance
but i cant reset ecu (need access to site)
any ideasyhanks in advance
↧
Add additional keys For Jaguar XE 2016
Hi mates, can anyone to edit FK72-19H440-AD dump to unlock add new key without replacing RFA (KVM) module? Thanks in advance.
| Q384.zip | ||
| File Type: |
|
 |
| Downloaded: | 0 times | |
| Size: | 120.2 KB | |
↧
ford focus airbag fault
56 reg. diesel. have a airbag light on. fault b2477 configuration fault. fault will not clear. can someone check the as built data in file attached. if incorrect could someone help with correct asbuilt file. thanks
| FocomAsbuilt_RCM_4M5T-14B056-BJ.zip | ||
| File Type: |
|
|
| Downloaded: | 1 times | |
| Size: | 507 bytes | |
↧
↧
Ford Galaxy bcm fault
2012 reg. Keyless . Bcm is water damaged. Is it possible to program a secondhand bcm, if so what tool is needed and what programming.
↧
Range Rover KVM virgin files.
Hi guys... i have virgin range rover kvm files complete. Read by xprog. For KVM DPLA and BJ32. I bought a virgin kvm from range rover for one costumers car but i did a read and back up before i used the kvm. Im sure it will help many others.
Thanks and rep would be nice. Its pass free for mhhauto.com
Thanks and rep would be nice. Its pass free for mhhauto.com
| kvm virgem.zip | ||
| File Type: |
|
|
| Downloaded: | 5 times | |
| Size: | 115.98 KB | |
↧
Ford Pcm Programming.
Hi everyone
I have a Ford ECO SPORT 2011 model,
The Car's PCM is faulty, I found an Old Used PCM ,Its part number is different,
how can i program this ecu, I have this FORD VCM OBD, but i lost its software.
if i get the software for this cable will it do the job or do i need something else.
please let me know.
I have a Ford ECO SPORT 2011 model,
The Car's PCM is faulty, I found an Old Used PCM ,Its part number is different,
how can i program this ecu, I have this FORD VCM OBD, but i lost its software.
if i get the software for this cable will it do the job or do i need something else.
please let me know.
↧
JLR help please
Hello mates, i Have Windows 10 64 Bits Can i install JLR 145, or 155?
I try to install JLR 145, But when i execut the Patch a message appears "Error not support X64"
Obs: I tried to run ->> mklink \D "C:\ Program Files (x86)\JLR" , but dont work.
Can someone help? Thank you!!
I try to install JLR 145, But when i execut the Patch a message appears "Error not support X64"
Obs: I tried to run ->> mklink \D "C:\ Program Files (x86)\JLR" , but dont work.
Can someone help? Thank you!!
↧
↧
Ford S-max 2009 SID206 AT need good calibration PCM
Hello
I have S-max 2.0TDCI SID206 AT transmission with software problem. TCM say wrong data from PCM.
This car have stolen PCM and somebody put another secondhand ecu and start the car but transmission working in emergency mode.
VIN: WF0SXXGBWS9C69657
ECU label: SID 206 , 6U71-12A650-KB
5WS40508 B-T , J38AC
UCDS SCAN:
PCM
Part Number: 8G91-12A650-GC
Current Version: 8G91-12K532-AC
TCM
Part Number: 7G9N-14C336-DB
Current Version: 7G9N-14C337-JJ
I think problem must be in wrong calibration in PCM
Regards
I have S-max 2.0TDCI SID206 AT transmission with software problem. TCM say wrong data from PCM.
This car have stolen PCM and somebody put another secondhand ecu and start the car but transmission working in emergency mode.
VIN: WF0SXXGBWS9C69657
ECU label: SID 206 , 6U71-12A650-KB
5WS40508 B-T , J38AC
UCDS SCAN:
PCM
Part Number: 8G91-12A650-GC
Current Version: 8G91-12K532-AC
TCM
Part Number: 7G9N-14C336-DB
Current Version: 7G9N-14C337-JJ
I think problem must be in wrong calibration in PCM
Regards
| UCSD SCAN2.jpg | ||
| File Type: |
|
|
| Downloaded: | 4 times | |
| Size: | 318.59 KB | |
↧
ford focus 2010 strange problem
hello guys
i have ford focus year 2010, 1.4 petrol. sometimes the car doesn't start ( almost when is hot ) , and i have dtc U0155- LOST COMMUNICATION WITH THE INSTRUMENT PANEL CLUSTER CONTROL MODULE.
i opened instrument cluster, solved everything and same problem
i changed instrument cluster and same problem (the problem came after some km drive or when the car is hot )
any help guys?
regards
i have ford focus year 2010, 1.4 petrol. sometimes the car doesn't start ( almost when is hot ) , and i have dtc U0155- LOST COMMUNICATION WITH THE INSTRUMENT PANEL CLUSTER CONTROL MODULE.
i opened instrument cluster, solved everything and same problem
i changed instrument cluster and same problem (the problem came after some km drive or when the car is hot )
any help guys?
regards
↧
F250 electrical problems
Hoping someone can help me out. I have a 2001 Ford F250 Super Duty that is giving me electrical problems. First off randomly has a dead battery might stay up for a week and then one morning be Dead. Sometimes when you turn the key off the radio stays on all night even without the key being in the ignition. Sometimes the climate control stays on with the key off sometimes it doesn't. Interior light stays on all the time with our doors are open or not. Door ajar light works on the dash when you open the doors one of the time so the switches are working. Once started it charges good new terminals new cables and runs great.
↧
Discovery 3 TCM burned
Hello mates! I have in my mechanical workshop a Land Rover Discovery 3.
This car was whased and burned the TCM module. I buy a used TCM of another DISCOVERY 3.
Now, i dont have comunication with several modules.
I already tested Can line, and is ok.
Need i to program the TCM to re-comunicate with all modules?
Thank You
This car was whased and burned the TCM module. I buy a used TCM of another DISCOVERY 3.
Now, i dont have comunication with several modules.
I already tested Can line, and is ok.
Need i to program the TCM to re-comunicate with all modules?
Thank You
↧
↧
Ford As Built Data please
can someone please upload ford complete build data for my ecosport please
VIN:MAJAXXMRKADC62870
need pcm and bcm also please
thanks in advance
sraj
VIN:MAJAXXMRKADC62870
need pcm and bcm also please
thanks in advance
sraj
↧
focus mk 2 swap transmission
hello
i swap automatic cvt to manual transmission. i reflash pcm with ids and all is fine except final drive ratio. i have error " tire axle out of acceptable range". somebody can help me with this?
best regards
i swap automatic cvt to manual transmission. i reflash pcm with ids and all is fine except final drive ratio. i have error " tire axle out of acceptable range". somebody can help me with this?
best regards
↧
Ford transit starting issues
Hi guys wanted to see if any one could help me with this issue I have with this ford transit, I’m a vag guy so not quite sure where to go with this one at the moment, the customer was driving it when it just lost power they pulled over and it cut out , I did have codes stored
U00140-00 lost comms with body control module
P2265-64 water in fuel sensor range/performance
P0120-84 throttle/pedal position sensor ‘A’ circuit
P068A-00 ECM/PCM power relay de-energised too early
U0167-00 lost comms with vehicle immobiliser control module
Codes U00140-00, P0120-84, U0167-00
All return ,
Currently the vehicle just turns over and doesn’t seem to fire over at all , I’m guessing there is some immobiliser issue but I am not sure how to go about diagnosing or repairing there issue ,
Hopefully some one can help me with this many thanks in advance aaron
Sent from my iPhone using Tapatalk
![[Image: 8915983ce402d0d25fad7c9cdd6ecd9f.jpg]]()
Sent from my iPhone using Tapatalk
U00140-00 lost comms with body control module
P2265-64 water in fuel sensor range/performance
P0120-84 throttle/pedal position sensor ‘A’ circuit
P068A-00 ECM/PCM power relay de-energised too early
U0167-00 lost comms with vehicle immobiliser control module
Codes U00140-00, P0120-84, U0167-00
All return ,
Currently the vehicle just turns over and doesn’t seem to fire over at all , I’m guessing there is some immobiliser issue but I am not sure how to go about diagnosing or repairing there issue ,
Hopefully some one can help me with this many thanks in advance aaron
Sent from my iPhone using Tapatalk
![[Image: 8915983ce402d0d25fad7c9cdd6ecd9f.jpg]](http://uploads.tapatalk-cdn.com/20190201/8915983ce402d0d25fad7c9cdd6ecd9f.jpg)
Sent from my iPhone using Tapatalk
↧
2011 Ford Fiesta- TCM Lost communication
This car came to me with unable to shift the lever from Park to any other gear position, scan was unable to
COmmunicate with the tcm, after further checks, came out that the tcm was bad..
I got two from the junk yard, and one refurbished as well.. now all tcm is now 3,
Anyone’s i fix the car, I can now communicate with it via the scan tool. But the IPC keep complaining of U0101 in it module, and abs also complained. That lost comm with tcm. But when you scan tcm or perform health report scan, you see the tcm responding.
Yet I can shift lever from P to any gear still..
I try to perform online coding with my drewtech passthru device but fjds software says tester can’t detect he tcm, burn if I use Launch or Autel scan tool, to scan I get communications to the tcm, pleaseI need advice as to what To do to make the IPC stop saying lost comm my
COmmunicate with the tcm, after further checks, came out that the tcm was bad..
I got two from the junk yard, and one refurbished as well.. now all tcm is now 3,
Anyone’s i fix the car, I can now communicate with it via the scan tool. But the IPC keep complaining of U0101 in it module, and abs also complained. That lost comm with tcm. But when you scan tcm or perform health report scan, you see the tcm responding.
Yet I can shift lever from P to any gear still..
I try to perform online coding with my drewtech passthru device but fjds software says tester can’t detect he tcm, burn if I use Launch or Autel scan tool, to scan I get communications to the tcm, pleaseI need advice as to what To do to make the IPC stop saying lost comm my
↧
↧
P1000 code f150
Hi there I’m having trouble getting my p1000 code to clear on my 2003 f150 5.4 I also have a p0500 code and a B1318 code present not sure if the others are causing it not to clear I’ve driven 200 miles b p1000 is still active please any help will be much appreciated.
↧
P0020, F150 2004 5.4L
Hi friends,
Please, I have issue with my Repair data.
What Pin and connector on PCM is the GND to camshaft actuator Bank2 of F150 04 5.4L?
Thanks in advance.
Please, I have issue with my Repair data.
What Pin and connector on PCM is the GND to camshaft actuator Bank2 of F150 04 5.4L?
Thanks in advance.
↧
2014 rangerover sport tyre pressure montor help
i fitted new Tyre pressure sensor how to reset it and rear spare wheel Tyre presser sensor location cant find thanks
↧